ISO (E). PDF disclaimer. This PDF file may contain embedded typefaces. In accordance with Adobe’s licensing policy, this file. Buy ISO (R) WELDING – WELDING OF REINFORCING STEEL – PART 2: NON LOAD-BEARING WELDED JOINTS from SAI. ILNAS-EN ISO Welding – Welding of reinforcing steel – Part 2: Non load- bearing welded joints (ISO ). Soudage.
|Published (Last):||13 September 2009|
|PDF File Size:||11.61 Mb|
|ePub File Size:||7.31 Mb|
|Price:||Free* [*Free Regsitration Required]|
NBN EN ISO | NBN
Iwo welding coordination personnel shall take remedial measures in cases of imperfections. Company organization, management and quality. Load-bearing welded joints are covered by ISO This part of ISO is applicable to the welding of weldable reinforcing steel and stainless reinforcing steel of non load-bearing welded joints, in workshops or on site.
Whenever the welding conditions, e.
BS EN ISO 17660-2:2006
Annex D is an example form and should be used where appropriate. You may experience issues viewing this site in Internet Explorer 9, 10 or Additional appropriate actions shall be taken, and records of such actions shall be maintained. Welding – Welding of reinforcing steel – Part 2: ISOQuality requirements for fusion welding of metallic materials — Part 4: The welding procedure specification shall be available for inspection at the workplace see Clause Shopping cart Close cart 0, foreach: Textile and leather technology Load-bearing welded joints are covered by ISO Except as permitted under the Copyright, Designs and Patents Act no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means — electronic, photocopying, recording or otherwise — without prior written permission from BSI.
In the case of continuous production using the same qualified welding procedure in workshops, the time period between production weld tests shall be defined and shall not exceed six months.
The range of qualification is given by the diameter ratio used. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Non load-bearing welded joints Status: Search all products by.
For reinforcing and structural steels, the CEV shall be in accordance with the product standard, and shall be calculated in accordance with the following equation: It is identical with ISO Taking these issues into account, it is apparent that both the welder and the welding coordinator require a specific level of skill and job isi and that special procedures for quality assurance need to be adopted.
Valid Buy this standard. BS EN ISO also covers welded joints between reinforcing steel bars and other steel components, such as connection devices and insert anchors, including prefabricated assemblies.
The length of the weld l and throat thickness a depend on the application, and shall 1760-2 in accordance with the WPS. Agt, may be required and measured, depending on the material standard being used or the design specification. However, the WPS shall be supplemented with the additional essential parameters in Clause When you use our service you can be assured the latest editions and easy access. NOTE For the surveillance of the welding works, the welding coordinator can be assisted by employees of the manufacturer with sufficient welding training or experience.
Health care technology Mining and minerals Soudage des aciers d’armatures.
BS EN ISO 钢筋的焊接-非承载焊缝 – MBA智库文档
Revisions British Standards are updated by amendment or revision. This 16760-2 Standard shall be given the status of a national standard, either by publication of 16760-2 identical text or by endorsement, at the latest by Marchand conflicting national standards shall be withdrawn at the latest by March Other mechanical properties, e.
Spot, seam and projection welding ISOSteel for the reinforcement and prestressing of concrete — Test methods — Part 1: It specifies requirements for materials, design and execution of welded joints, welding personnel, quality requirements, examination and testing. All test pieces shall be visually inspected prior to testing. Log In Sign Up. Read more about 17606-2 Subscriptions. At the end of the training period, the welders shall weld a relevant number of test specimens e.
Welding – Welding of reinforcing steel – Part 2: Non load-bearing welded joints (ISO 17660-2:2006)
For other processes, acceptance criteria apply in accordance with the relevant standard for procedures. The report shall clearly state whether or not the requirements of this part of ISO have been met. Road vehicles engineering One of the principal differences between BS and this standard is that BS offered more practical guidance on the welding process issues, some of these issues have been highlighted in the National Annex and further guidance can be found in parts 1 to 3 of BS EN The welding parameters shall be set in accordance with the appropriate WPS before welding.
Assemblages non transmettants ISO For dated references, only the edition cited applies. Please note that the selected standard is invalid. Recommended test specimens are given in Annex B.
The welds shall not influence significantly the full load-bearing capacity and ductility of the bars, and the welding procedure may not cause embrittlement of the material. Undercuts may influence the transmittable force.
For welded joints in reinforcing steel made by arc-welding 17660- only those test specimens that have met the requirements of quality level D for surface imperfections, as appropriate except undercut, where quality level C appliesin accordance with ISOshall be subject to further mechanical testing.
Take the smart route to manage medical device compliance. NOTE 1 To avoid loss of strength, it is advisable that the heat input be limited when using specific types of reinforcing steels, e. Petroleum and related technologies